| Chockfast® Pourable Chocking Compounds |
 |
Chockfast® Orange
Conveniently pourable, two-component, structural epoxy “chock” that replaces tediously fitted steel shims (or steel chocks) assuring intimate contact with machined or un-machined equipment bedplates. Virtually 100% effective bearing underneath supported equipment. |
[Technical Bulletin]
659G 
|
|
|
 |
Chockfast® Black [Chockfast Black Video]
Black Pourable, two-component, deep-pour structural epoxy “chock” used to support and maintain permanent frame alignment under hot-running machinery; allows free flow of air between equipment and foundation to lower foundation temperatures and minimize upward thermal growth; virtually 100% effective bearing underneath supported equipment; normally poured in thickness’ of 1-1/4”—2-1/2”. |
[Technical Bulletin]
666G
|
|
|
 |
Chockfast® Gray
Highly flowable, two-component, thin pour “chock” designed to maintain proper alignment and support of machinery and equipment; able to withstand severe industrial environments with a high degree of both physical and thermal shock resistance. |
[Technical Bulletin]
656G
|
|
|
 |
Chockfast® Red SG
Red SG Chockfast Red SG is a three component, high strength, 100% solids epoxy grouting compound which is used to grout large machinery and to support soleplates in all types of foundation designs with clearances as little as 25mm (1"). Chockfast Red SG has extremely high physical properties and negligible shrinkage, making it ideal for final positioning of critically aligned equipment within close tolerances. |
[Technical Bulletin]
618I
|
|
|
|
General Guidelines for Marine Chock Designers
Using Chockfast® Orange & Gray |
[Technical Bulletin]
692D |
|
|
| Back to Top |
Chockfast® Guidelines for Stern Tubes |
[Technical Bulletin]
632C |
| Adhesives |
|
Phillybond TA-30
Tile Adhesive - Adhesive and Grout - QPL - MIL-A-24456
Phillybond TA-30 a two component, high tack strength epoxy for general bonding and structural applications. TA-30 adhesive will support 5 lbs per sq. ft. on overhead or vertical surfaces while curing. |
[Technical Bulletin]
958A
|
|
|
|
Phillyclad 1775/620TS
Phillyclad 1775/620TS is an excellent general purpose, nontoxic laminating resin system for FRP application requiring rapid and thorough wet out. Excellent for use as a thin laminate protective coating over steel or wood and fabrication of molded fiberglass structures or components. |
[Technical Bulletin]
950B
|
|
|
|
Phillybond® Orange - Flexible Stern Tube Sealant
PHILLYBOND ORANGE is a two component, epoxy paste, developed for sealing exposed edges of CHOCKFAST in stern tube applications. It is resistant to sea water and lubricating oils. It has good adhesive strength and flexibility over a wide temperature range. Because of its paste-like consistency, it can be applied in thick, vertical applications without sagging, yet is easy to trowel and provide a smooth finished surface. |
[Technical Bulletin]
646D
|
|
|
| Back to Top |
Phillymastic TG-7B - for LNG/LPG Tank Installation
Phillymastic TG-7B is a two-component, load-bearing, epoxy mastic specifically developed for LNG/LPG tank or container system installations where shimming or void-filling of supporting components is required. TG-7B provides excellent load-bearing and adhesive properties at cryogenic temperatures assuring evenly distributed loads across all tank supports. This mastic is available as either a pourable liquid or a trowelable paste. Both can be mixed either by hand or with automatic dispensing equipment. |
[Technical Bulletin]
1025A
|
| Repair Products |
|
Super Ceramic Repair Liquid
SUPER CERAMIC Repair Liquid is a unique ceramic filled, high build, brush able epoxy coating. Formulated for unequaled chemical and corrosion resistance with outstanding wear properties under adverse environments. SUPER CERAMIC Repair Liquid is ideally suited for lining and resurfacing all types of severe service equipment commonly found in chemical plants, power plants, pulp & paper mills, mining operations, water treatment plants and a variety of other industrial and marine applications. |
[Technical Bulletin]
819F
|
|
|
|
Super Alloy Titanium Repair Compound
The latest in high technology, high bond strength repair systems. Use to join such dissimilar metals as iron, steel, aluminum, tungsten carbide, brass, zinc, and zinc alloys without the problems of galvanic corrosion. Adheres tenaciously to properly prepared surfaces. Hardens to a rigid metallic mass which permits drilling, tapping, or machining with ordinary metalworking tools. Maintains an integral bond, a high level of resistance to impact, abrasion, chemicals and high temperature. |
[Technical Bulletin]
820K
|
|
|
|
Super Ceramic Repair Putty
A smooth ceramic-filled epoxy putty with exceptional wear resistance. The "noslump" nature makes it ideal for repairing overhead, vertical or curved surfaces. Well suited for the repair of severe service equipment commonly found in a variety of industrial and marine applications. |
[Technical Bulletin]
821G
|
|
|
|
Phillybond® #6
A 2-component, high strength epoxy paste for the repair of punctures or cracks in tanks, pumps, pipes, steam lines, sea chests, valve bodies, and many other applications. The material is also used to fill holes, voids and to provide a smooth surface for repairs at temperatures up to 428°F (220°C). Resistant to most acids, alkali and hydrocarbons and will adhere to clean surfaces such as steel, cast iron, bronze, aluminum, copper, nickel, wood and most plastics. |
[Technical Bulletin]
470
|
|
|
|
Phillyclad® #8
A 2-component, fast-setting epoxy laminating resin system designed for high strength fiberglass reinforced repairs to pipes, tanks, valves, and other equipment subject to corrosion or erosion. Used to repair leaks in areas at operating temperatures to 428°F (220°C). Excellent resistance to salt water, crude and refined oil, gasoline, caustics and most acids. |
[Technical Bulletin]
966B
|
|
|
| Back to Top |
ITW Repair Compound
A 2-component, 100% solids, epoxy paste developed specifically for filling, smoothing and fairing applications on metals, plastics (FRP), wood or masonry. Smooth consistency and excellent non-sagging properties. Excellent resistance to fresh water, salt water, crude and refined oils, gasoline, jet fuel. Provides a tough, uniform surface that will readily accept any top coating or lining. The cured epoxy is readily sanded or ground. The excellent feathering properties facilitate achieving a precision surface profile or smoothness. Contains no metallic fillers. |
[Technical Bulletin]
1015B
|
| Industrial Coatings |
|
Phillyclad 5066
A is a two component, heavy duty coating designed for applications requiring a high degree of resiliency combined with excellent adhesion and impact properties. The compound is resistant to oils, fuels and most chemicals, is nontoxic and contains no volatiles. PHILLYCLAD 5066A is self-extinguishing and meets the requirements of ASTM-D-635. |
[Technical Bulletin]
946A
|
|
|
 |
Impax® 300
Heavy Duty Epoxy Anti-Slip. A catalyzed epoxy anti-slip coating exhibiting superior chemical resistance to acids, alkalis, solvents, fuels, etc. Easy to mix and apply, this anti-slip coating can be applied to concrete, steel and wood. |
[Technical Bulletin]
408A
|
|
|
 |
Impax® 2001 CRE
Novolac Epoxy. A heavy duty, interior, two-component novolac epoxy coating formulated for demanding industrial requirements. It dries quickly to a tough, semi-gloss finish with excellent resistance to alkali, abrasion, corrosion and chemicals. |
[Technical Bulletin]
438C
|
|
|
|
Impax® IXT-59 Solvent
IMPAX IXT-59 is an aromatic hydrocarbon solvent used for general epoxy cleanup of tools and equipment used for mixing and applying epoxy materials. It must be used before the epoxy has set. Formerly known as PRT-59, IXT-59 is also used for removing grease, oil and other contaminants from surfaces prior to applying epoxy materials. |
[Technical Bulletin]
859C
|
|
|
 |
Impax® Rust Inhibitive Primer
A lead and chromate free, rust inhibitive, two component epoxy primerspecifically designed for use in conjunction with Philadelphia Resins coatings applied to m+etal substrates.It also meets USDA standards for maintenance protective coatings not in direct contact with food infederally inspected meat and poultry plants. |
[Technical Bulletin]
1021F
|
| Back to Top |
|
